Shield Rifleworks

BOLT ACTION MANUAL

THIS MANUAL APPLIES TO ALL RDSC | SHIELD RIFLEWORKS BOLT ACTION RIFLES, ACTIONS AND BARRELLED ACTIONS. THE MANUAL INCLUDES EXPLANATIONS AND DESCRIPTIONS OF STANDARD AS WELL AS OPTIONAL FEATURES AND EQUIPMENT. PLEASE FOLLOW MATERIAL THAT IS APPLICABLE TO YOUR SPECIFIC RDSC | SHIELD RIFLEWORKS RIFLE.

INDICATIONS IN THIS MANUAL

Warning

A WARNING indicates a condition in which accident, serious injury or even death could result if the WARNING is neglected.

CAUTION

A CAUTION indicates a condition that can cause damage to your weapon if the CAUTION is neglected.

NOTICE

A NOTICE indicates a condition that can be interesting or helpful in the corresponding subjects.

IMPORTANT PRECAUTIONS

Warning

FIREARMS CAN BE DANEROUS AND CAN POTENTIALLY CAUSE SERIOUS INJURY, DAMAGE TO PROPERTY OR DEATH, IF HANDLED IMPROPERLY. THE FOLLOWING SAFETY RULES ARE AN IMPORTANT REMINDER THAT FIREARM SAFETY IS YOUR RESPONSIBILITY.

Warning

Always ensure that the safety is engaged until ready to fire weapon.

CAUTION

RDSC | Shield Rifleworks and/or its distributors assume no liability for product malfunction or for physical injury or property damage resulting in whole or in part from criminal or negligent use of the product, improper or careless handling, unauthorized modifications, use of defective, improper or hand-loaded, reloaded or remanufactured ammunition, customer misuse or neglect of the product, or other factors beyond the Manufacturer’s direct and immediate control.

Warning

Read the entire manual carefully before using this firearm. Make sure that any person using or having access to this firearm reads and understands this entire manual prior to use or access.

Warning

Do not attempt to load more cartridges into your firearm than local legislation permits. RDSC | Shield Rifleworks will not be held responsible for any product malfunction, property damage, physical injury or legal repercussions which have been caused through not abiding by the loading instructions stated in the RDSC | Shield Rifleworks product manual. Alterations or adjustments to any part of the rifle which change the ammunition capacity voids the manufacturer’s warranty.

All information contained in this instruction manual is accurate at the time of publication. The descriptions and illustrations given are intended for general guide only, and must not be taken as binding. RDSC | Shield Rifleworks reserves the right to make any changes it thinks necessary to improve its models or meet any requirements of manufacturing or commercial nature, at any moment and without notice.

Warning

FIREARMS CAN BE DANGEROUS AND CAN POTENTIALLY CAUSE SERIOUS INJURY, DAMAGE TO PROPERTY OR DEATH, IF HANDLED IMPROPERKY. THE FOLLOWING SAFETY RULES ARE AN IMPORTANT REMINDER THAT FIREARM SAFETY IS YOUR RESPONSIBILITY.

CAUTION

READ THIS MANUAL CAREFULLY PRIOR TO USING THE FIREARM.

BASIC FIREARMS SAFETY RULES

NEVER POINT A FIREARM AT SOMETHING THAT IS NOT SAFE TO SHOOT.
Never let the muzzle of a firearm point at any part of your body or at another person. This is especially important when loading or unloading the firearm. When you are shooting at a target, know what is behind it. Some bullets can travel over 5 miles. If you miss your target or if the bullet penetrates the target, it is your responsibility to ensure that the shot does not cause unintended injury or damage.
ALWAYS TREAT A FIREARM AS IF IT WERE LOADED.
Never assume a firearm is unloaded. The only certain way to ensure there are no cartridges in a firearm is to open the chamber and visually and physically examine the inside to see if a round is present. Removing or unloading the magazine will not guarantee that a firearm is unloaded or cannot fire. Shotguns and rifles can be checked by cycling or removing all rounds and by then operating and inspecting the chamber so that a visual inspection of the chamber for any remaining rounds can be made.
STORE YOUR FIREARM SO THAT CHILDREN CANNOT GAIN ACCESS TO IT.
It is your responsibility to ensure that children under the age of 18 or other unauthorized persons do not gain access to your firearm. To reduce the risk of accidents involving children, unload your firearm, lock it and store the ammunition in a separate locked location. Please not that devices intended to prevent accidents – for example, cable locks, chamber plugs, etc. - may not prevent use or misuse of your firearm by a determined person. Firearm storage in a steel gun safe may be more appropriate to reduce the likelihood of intentional misuse of a firearm by a child or unauthorized person.
NEVER SHOOT AT WATER OR AT A HARD SURFACE.
Shooting at the surface of water or at a rock or other hard surface increases the chance or ricochets or fragmentation of the bullet or shot, which can result in the projectile striking an unintended or peripheral target.
KNOW THE SAFETY FEATURES OF THE FIREARM YOU ARE USING, BUT REMEMBER: SAFETY DEVICES ARE NOT A SUBSTITUTE FOR SAFE HANDLING PROCEDURES.
Never rely solely on a safety device to prevent an accident. It is imperative that you know and use the safety features of the particular firearm you are handling, but accidents can best be prevented by following the safe handling procedures described in these safety rules and elsewhere in the product manual. To further familiarize yourself with the proper use of this or other firearms, take a Firearms Safety Course taught by an expert in firearms use and safety procedures.
PROPERLY MAINTAIN YOUR FIREARM.
Store and carry your firearm so that dirt or lint does not accumulate in the working parts. Clean and oil your firearm following the instructions provided in this manual, after each use to prevent corrosion, damage to the barrel or accumulation of impurities which can prevent use of the firearm in an emergency. Always check the bore and chamber prior to loading to ensure that they are clean and free from obstructions. Firing with an obstruction in the barrel or chamber can rupture the barrel and injure you or others nearby, in the event you hear an unusual noise when shooting, stop firing immediately, engage the manual safety and unload the firearm. Make sure the chamber and barrel are free from any obstruction, like a bullet blocked inside the barrel due to defective or improper ammunition.
USE PROPER AMMUNITION
Use only factory-loaded, new ammunition manufactured to industry specifications: CIP (Europe and Elsewhere), SAAMI© (U.S.A.). Be certain that each round you use is the proper caliber or gauge and type for the particular firearm. The caliber or gauge of the firearm is clearly marked on the barrels of rifles/shotguns and on the slide or barrel of pistols. The use of reloaded or remanufactured ammunition can increase the likelihood of excessive cartridge pressures, case-head ruptures or other defects in the ammunition that can cause damage to your firearm and injury to yourself or others nearby.
ALWAYS WEAR PROTECTIVE GLASSES AND EARPLUGS WHEN SHOOTING.
The change that gas, gunpowder or metal fragments will blow back and injure a shooter who is firing a gun is rare, but the injury that can be sustained in such circumstances can be severe, including the possible loss of eyesight. A shooter must always wear impact resistant shooting glasses when firing any firearm. Noise-reducing earplugs or headphones will reduce the risk of damage to hearing caused by prolonged shooting activity.
NEVER CLIMB A TREE, FENCE OR OBSTRUCTION WITH A LOADED FIREARM.
Open and empty the chamber of your firearm and engage the manual safety before climbing or descending a tree or before climbing a fence or jumping over a ditch or other obstruction. Never pull or push a loaded firearm toward yourself or another person. Always unload a firearm, visually and physically inspect to see that the magazine, loading mechanism and chamber are unloaded, and action is open before handing it to another person. Never take a firearm from another person unless it is unloaded, visually and physically checked to confirm it is unloaded, and the action is open.
AVOID ALCOHOLIC BEVERAGES OR JUDGEMENT IMPARING MEDICATION WHEN SHOOTING.
Do not drink and shoot. If you take medication that can impair motor reactions or judgements, do not handle a firearm while you are under the influence of the medication.
NEVER TRANSPORT A LOADED FIREARM.
Unload a firearm before putting it in a vehicle (chamber and magazine empty). Hunters and target shooters should load their firearm only at their destination, and only when they are ready to shoot. If you carry a firearm for self-protection, leaving the chamber unloaded can reduce the chance of an unintentional discharge.
LEAD WARNING.
Discharging firearms in poorly ventilated areas, cleaning firearms, or handling ammunition may result in exposure to lead and other substances known to cause birth defects, reproductive harm, and other serious physical injury. Always Have adequate ventilation. Wash hands thoroughly after exposure.

CAUTION

It is YOUR responsibility to know and abide by Federal, Provincial and Local laws governing the sale, transportation and use of firearms in your area.

Warning

This firearm has the capability of taking your life or the life of someone else! Always be extremely careful with your firearm. An accident is almost always the result of not following basic firearm safety rules.

RDSC | Shield Rifleworks manufactures precision bolt-action rifles designed for accuracy and modularity. Key components include:

RECEIVER: Houses the bolt and firing mechanism.
BOLT: Manually operated to chamber and eject spent cartridges.
BARREL: Match grade and available in various calibers, contours and lengths.
TRIGGER ASSEMBLY: Aftermarket 3rd party manufactured, factory-set for optimal pull weight.
SAFETY: Aftermarket 3rd party manufactured, two position safety depending on configuration.
MAGAZINE: Aftermarket 3rd party manufactured, detachable box magazine for quick loading.
STOCK/CHASSIS: Aftermarket 3rd party manufactured with optional handguard, stock, and magazine configurations.

ASSEMBLY INSTRUCTIONS

Warning

CAUTION

RDSC | Shield Rifleworks assumes no liability for any injury or damage to property resulting from improper or careless handling, or intentional or accidental firing of the rifle.

Warning

All assembly, disassembly and maintenance procedures should be carried out with the firearm unloaded. Inspect the firearm by looking through the barrel from the rear end of the receiver. During assembly, disassembly and maintenance procedures, never point a firearm at someone or at hard or flat surfaces. Always treat the firearm as if it were loaded.

NOTICE

It is advisable to carry out the assembly operation over a table to catch components should they drop.

Before first use:

Clean the Barrel: Run a dry patch from breech to muzzle to remove oil.
Inspect the Bolt: Ensure bolt assembly surfaces are well lubricated. (Do not run the bolt assembly dry.)
Check Receiver Screws: Tighten securely to proper spec (Chassis mfg. dependent)
Install Bolt: Slide bolt into receiver, while holding the bolt catch down until it engages the bolt body track.
Mount Optics (if applicable): Use compatible scope rings and follow manufacturer instructions to install.

After performing the above check points, your rifle is now ready for test firing. NOTE: If, after reading this manual, you have any questions about the maintenance, operation or use of your rifle, consult your dealer. Before using the firearm, you must thoroughly familiarize yourself with its use and operation, and with safe firearm handling in general.

Warning

Store your firearm so that children or other people not familiar with firearms cannot gain access to it. To reduce the risk of accidents involving children, unload your firearm and lock it away. Store the ammunition in a separate locked location.

MECHANICAL SAFETY OPERATION

RDSC | Shield Rifleworks utilizes reputable 3rd party trigger manufacturers (US-made only.)

Fire (Forward position): Safety disengaged.
Safe (Rear position): Safety engaged.
Transport: Unloaded, bolt removed. (recommended)

Warning

The Manual safety is merely a mechanical device and is in no way a substitute for the Basic Safety Rules for handling firearms.

LOAD CHECK

At several points in this manual, you will be instructed to visually and physically check that your rifle is unloaded. This should become second nature to you as should the following precautions.

Never assume the gun is unloaded
Never point or push a firearm toward yourself or another person.
Always visually check to see that the chamber is unloaded.
Remove the magazine and open the bolt before handing the rifle to another person
Never take from, or give, the rifle to another person unless the magazine is removed, the bolt is open, and the chamber has been visually checked to confirm it is unloaded.

To visually check to be certain your rifle is unloaded, carefully observe the following steps:

Warning

Keep your finger OFF THE TRIGGER and the barrel pointed in a safe direction.

Warning

When the safety selector is in the forward position, the SAFETY IS DISENGAGED, and the rifle is ready to fire. (forward position engraved "F" on the receiver) When the safety selector is in the rear position, the SAFETY IS ENGAGED. (rear position engraved "S" on the receiver)

Inspect the ejection port, the magazine and cartridge chamber as indicated in the following:

Engage the manual safety by moving the safety selector to the rear position.
Remove the magazine by depressing the magazine release button. (chassis/stock mfg. dependent)
Remove the bolt by lifting the bolt handle, pressing the bolt catch button and completely pulling the bolt out of the receiver.
Check the cartridge chamber to be certain it is empty. If the rifle is unloaded, proceed to the following step, otherwise refer to the procedure “Unloading the rifle”.
Reinsert the bolt into the receiver and close the bolt. THE FIRING PIN IS NOW COCKED. With the barrel pointed in a safe direction, de-cock the firing pin by pulling the trigger.

NOTICE

The firing pin can only be de-cocked when the bolt is in the closed position.

OBSTRUCTION CHECK

Warning

Always be certain the firearm is unloaded. Please refer to the “LOAD CHECK” section.

Check the barrel to ensure there are no obstructions in the chamber or bore. This is important because serious injury can result to the user or to nearby persons if a cartridge is fired in an obstructed barrel or chamber. Check the inside of the barrel and bore prior to inserting the bolt into the firearm and before use. If the bolt is already installed, use the following procedure:

Remove the magazine by depressing the magazine release button. (chassis/stock mfg. dependent)
Remove the bolt by lifting the bolt handle, pressing the bolt catch button and completely pulling the bolt out of the receiver.
Look through the barrel from the rear and make sure there are no obstructions, even minor ones.
If an obstruction in the barrel is detected, a competent gunsmith must remove the obstruction. The rifle should be inspected again before it can be fired.
Reinstall the bolt into the receiver.

AMMUNITION

Use only high-quality, commercially manufactured ammunition that is manufactured in accordance with C.I.P or SAAMI standards. Be certain that the ammunition is of the appropriate caliber and loading for the firearm and is clean, dry, and in good condition. The cartridge designation for your rifle is clearly engraved on the barrel.

Warning

Carefully inspect each cartridge before loading in the magazine. Be certain the cartridge cases are not split, deformed, or the cartridges do not possess any other dents or defects. This even applies to factory ammunition.

Do not fire old (age over 10 years) in this firearm. Primers, powders, cartridge cases, and bullets can deteriorate with time and cause damage to the firearm, or injury to the shooter or others. Lead bullets have a tendency to cause bore leading, which may dramatically increase the discharge pressure. Make sure to remove all chamber and bore lead accumulation after each use. DO NOT ever shoot with steel jacketed bullets or steel cartridge cases.

NOTICE

Use only high-quality ammunition and before purchasing a large batch, ensure that the rifle functions reliably with it.

Warning

Use only high quality, factory manufactured ammunition. The use of reloaded, handloaded, remanufactured or other non-standard ammunition voids all warranties, and may cause severe damage to the firearm and serious injury to the shooter or others. Improperly loaded ammunition can be extremely dangerous. Always use ammunition that complies with industry performance standards established by SAAMI or C.I.P., RDSC | Shield Rifleworks does not accept any liability for any damage or injuries caused by reloaded/handloaded or otherwise improper ammunition.

DRY FIRING / “DUMMY” ROUNDS

Dry firing is defined as firing a firearm with no ammunition in the chamber. Long term dry firing may damage the bolt. “Snap Caps” (chamber inserts that allow a firearm to be dry-fired without damaging the rifle) are a available at most gun stores for those who wish to practice firing without live ammunition.

“Snap cap” cartridges with spring loaded “primers” are ideal for dry firing the rifle. “DUMMY” cartridges with empty primer pockets are good for loading/unloading practice but DO NOT protect the firing pin during dry firing.

LOADING AND FIRING

Warning

RDSC | Shield Rifleworks assumes no responsibility for any injury or property damage resulting from improper or careless handling, intentional or accidental discharge of the firearm.
This rifle can have a live round in the chamber and can fire even if the magazine is empty or has been removed.
Before loading the firearm, become familiar with the following loading procedures without the use of ammunition.
Never handle a loaded firearm until you are fully familiar with the loading procedures. Always point the firearm in a safe direction.
Always keep your finger away from the trigger whenever you do not intend to fire. Make sure the rifle is not already loaded by removing the magazine and retracting the bolt in order to check that the chamber is empty.
Be sure that you have the correct cartridges for the rifle.
Make sure you have wiped cartridge chamber dry before shooting.
Always wear protective glasses and earplugs whenever you shoot, and make sure that people close to you are similarly protected.

LOADING THE MAGAZINE

Remove the magazine by depressing the magazine release button. (chassis/stock mfg. dependent)
Place a cartridge on the magazine follower in front of the lips at the top of the magazine and slide the cartridge completely under the lips until it is lodged fully inside the magazine body.
Repeat process until magazine is fully loaded.

NOTICE

Do not try to force more than the maximum number of rounds into the magazine. An overloaded magazine may not function properly.

LOADING AND FIRING

When the loaded magazine is inserted into the rifle, lift the bolt and pull it completely back. As the bolt is pushed forwards the cartridge is fed into the chamber and on rotating the handle downward the action is closed and the rifle is cocked.

Warning

The firearm is now loaded and ready to fire after the manual safety is disengaged. Always keep your finger off the trigger and avoid contact with the trigger by other objects if you do not intend to fire. Never point a firearm at something that is not safe to shoot.

To fire, disengage the safety (selector in the forward position) and pull the trigger.
Repeat the sequence to fire another round. If you do not plan to fire a second shot, engage the safety, keeping the firearm pointed in a safe direction and the fingers away from the trigger. If you have finished shooting, unload the rifle as indicated in “Unloading the rifle”.

Warning

If the rifle doesn’t fire after pulling the trigger, engage the safety, wait at least one minute and unload the rifle with extreme care as described in the corresponding section.

UNLOADING THE RIFLE

Warning

Always unload the firearm immediately after firing is completed. Never store a loaded firearm. To store the rifle, refer to the paragraph “Storage”.

Keeping the firearm pointed in a safe direction, engage the safety by pushing the selector to the rear position.
Lift and pull back the bolt to extract the live cartridge from the chamber.
Remove the magazine by pushing the magazine release button.
After checking the rifle is unloaded and empty of cartridges, close the bolt, point the rifle in a safe direction and pull the trigger, de-cocking the firing pin.
To unload the magazine, grip it with one hand around the magazine box, bottom down and front end forward/ with the tip of the thumb, firmly press down on the cartridge rim and push towards the front of the magazine box. As the cartridge moves forward, tip it slightly upward with the index finger. Repeat until the magazine is unloaded.

SIGHTS AND SCOPE

Warning

Always be certain the firearm is unloaded prior to adjusting the sights. Please refer to the instructions given in the “Load check” paragraph.

RIFLE SCOPE ASSEMBLY

To install a rifle scope, you will need the appropriate scope mounts. For more information, ask one of our RDSC | Shield Rifleworks customer reps. Use the scope manufacturer’s instructions when mounting scope to the rifle.

SIGHTING IN YOUR RIFLE

The following instructions are only generic guidelines to sight in the scope of the rifle. Specific procedures may vary depending on the scope make, and model.

The scope or sights need to be pre-aligned so that actual sighting in procedure is easier. Bore-sighting can be done with a specific bore-sighter OR following the procedure below.

Place the rifle solidly on a benchrest or other steady support and remove the bolt.
Place a target (paper sheet) at a distance of 25-30 yards.
Adjust the position of the rifle so that you can see the target through the bore. Make sure that the rifle remains stationary.
Look through the scope or sights and adjust windage and elevation so that the reticle centers on the same target you see through the bore.

After bore-sighting, final sighting in is done at a target set at 100-150 yards. Again it is best to do this from a solid bench rest or other steady support.

Follow the adjustment directions and other instructions given by the manufacturer of the rifle scope you will be using.

When you have prepared properly and are ready to start sighting in, take the following steps.

Aim at the bullseye and fire 3 shots.
Unload the rifle and check the shot grouping with binoculars or a spotting scope.
Adjust the elevation and windage of the scope so that the reticle moves to the center of the shot grouping
Repeat the procedure until shot grouping is hitting in the proximity of the bullseye.

DISASSEMBLY AND ASSEMBLY OF THE RIFLE COMPONENTS

Warning

Always check the firearm is unloaded. Inspect the firearm by looking through the ejection port and the chamber. If it is not empty. Unload the rifle as instructed in “Unloading the rifle” Check that the firing pin is de-cocked.
Never point the firearm at someone or at hard, flat surfaces. Always treat the rifle as if it is loaded.

NOTICE

It is advisable to carry out the assembly operation over a table to catch components should they drop.

BARRELLED RECEIVER

Remove the barreled receiver from the stock as follows.

Make sure the rifle is not loaded.
Remove the bolt and the magazine
Loosen and remove the two receiver fastening screws. (Chassis/stock mfg. dependent)
Remove the chassis/stock by pulling it downwards.
Carefully pull the barreled receiver out of the chassis/stock.

Installation is carried out in reverse order. Tighten the receiver screws to chassis/stock mfg. specifications.

BOLT

General disassembly of the bolt is not necessary nor recommended. If you have reason to believe that too much oil may have penetrated the bolt, you should clean it in order to maintain its smooth operation. This is particularly important in cold or harsh weather. The bolt can be removed as follows.

Remove the bolt by pushing the bolt catch and simultaneously pulling the bolt backwards.

The bolt should not require any further disassembly for cleaning purposes.

MAGAZINE

At times, you may need to disassemble the magazine in order to clean it from fouling, powder residue or dust. To do so, please follow these instructions.

Remove the bottom floor plate of the magazine by pressing the button in the center and simultaneously sliding the floor plate forward.
Remove the spring and follower from the bottom of the magazine body.
With the spring and follower out, wipe down the inside of the magazine by pulling a clean microfiber cloth through the hollow tube of the magazine body a couple of times.
Wipe down the spring and follower to remove any remaining dust and sand

Reassembly is the opposite of disassembly.

RIFLE ADJUSTMENTS

Warning

Always check the firearm is unloaded. Inspect the firearm by looking through the ejection port and the chamber. If it is not empty. Unload the rifle as instructed in “Unloading the rifle” Check that the firing pin is de-cocked.
Never point the firearm at someone or at hard, flat surfaces. Always treat the rifle as if it is loaded.

TRIGGER PULL WEIGHT

Warning

The sear engagement, safety and other components of the action are precision mechanisms, which were properly adjusted at the factory. They should not be altered, modified or changed. Modifications to the firearm may decrease its safety and increase the risk of serious injury.
For safety reasons, do not attempt to reduce the trigger weight below mfg. recommendations.
If the trigger assembly must be replaced. The trigger mechanism must be returned to the manufacturer.

Triggers are pre-set at 3 lbs pull weight and adjusted at the factory, and need no adjustment of any kind. However, if you wish to alter the trigger pull weight, follow the instructions below.

Remove the bolt and magazine.
Remove the stock and chassis from the barreled action, as instructed previously.
Remove the trigger assembly.
Screw (Figure 1) is the trigger pull adjustment screw. The pull is pre-set at 3 lbs. Turning the screw in (clockwise) will make the pull weight heavier while turning it out (counter-clockwise) will make it lighter. DO NOT REDUCE THE TRIGGER PULL WEIGHT BELOW 1.5 LBS. A VERY LIGHT WEIGHT OF PULL CAN CAUSE SLAM FIRES.
Reinstall the trigger assembly and stock and chassis to the barreled action.

CAUTION

Do not make any other adjustments to the trigger. If you notice any changes in the operation of the trigger, please turn to an authorized gunsmith.

MUZZLE BRAKE OR SUPPRESSOR ATTACHMENT

Your RDSC | Shield Rifleworks rifle may feature a muzzle thread, which enables attachment of a muzzle brake or suppressor. Attachment on the muzzle threads may vary between different muzzle brakes or suppressors.

Muzzle brake attachment is done as follows.

Remove the muzzle thread protector by turning it counter-clockwise
Attach the muzzle brake to the muzzle and tighten it by hand by turning clockwise.

Reverse the procedure to remove.

It is necessary to check the tightness of the muzzle brake if fired continuously. For more secure attachment, we recommend to apply small amount of Loctite 287 Thread locker (or similar) on the muzzle thread before attachment. Refer to the instructions of the thread locker manufacturer. Be careful not to spill the thread locker inside the bore or other functional surfaces.

CAUTION

Follow suppressor manufacturers instructions when installing the suppressor.

ROUTINE CLEANING AND MAINTENANCE

Warning

Always check the firearm is unloaded. Inspect the firearm by looking through the ejection port and the chamber. If it is not empty. Unload the rifle as instructed in “Unloading the rifle” Check that the firing pin is de-cocked.
Never point the firearm at someone or at hard, flat surfaces. Always treat the rifle as if it is loaded.

Routine cleaning should always take place right after use of the rifle (even without shooting). Maintenance should not be neglected even in the case of the stainless models. Corrosion can begin within 24 hours if the rifle is not cleaned after use. It is recommended to support the rifle with a bi-pod during cleaning. Use only high-quality gun oil that cleans, lubricates and preserves. Routine cleaning procedure is done as follows

Ensure the rifle is unloaded and remove the bolt and magazine
In case the rifle has been used in wet conditions dry it using compressed air or let it dry in a warm/dry place without any protective cover.
Use a straight, sturdy and smooth cleaning rod fitted with bronze bore brush soaked in bore solvent and push-pull it through the bore until major residue is removed. It is recommended to use the cleaning rode guide to prevent the rod from dragging on the inner surfaces of the bore and receiver.
Push a clean felt pellet moistened with cleaning solvent through the bore one after another until pellets come out clean. Clean only in the direction of bullet movement and replace dirty pellet with new before every cleaning sequence. Guide the cleaning rod with fingers or special bore guide.
Clean the inner surfaces of the receiver from all the firing residue with felt pellet and/or brush moistened with cleaning solvent.
Use a small solvent-wetted brush to clean the bolt from firing residue.
Use larger diameter nylon brush to clean the bolt from firing residue
Pass a regular bore pellet moistened with rust preventative oil through the bore. Leave a thin coat of oil on the cartridge chamber surface. (Remember to wipe it dry before shooting).
Wipe all touching surfaces of the receiver and bolt with a very light coat of rust preventative oil.
Check the correct tightness of the receiver screws.

PERIODIC MAINTENANCE

Warning

Always check the firearm is unloaded. Inspect the firearm by looking through the ejection port and the chamber. If it is not empty. Unload the rifle as instructed in “Unloading the rifle” Check that the firing pin is de-cocked.
Never point the firearm at someone or at hard, flat surfaces. Always treat the rifle as if it is loaded.

Periodic maintenance should be carried out at least once a year or more frequently under heavy use or in severe conditions. Periodic maintenance is recommended if the rifle is to be stored for prolonged period. If it is necessary to replace any parts, use only factory spare parts. Periodic maintenance is carried out as follows.

Carry out the routine cleaning and maintenance.
It is advisable to remove copper fouling from the bore. When examining the front part of the bore, slight residue from the bullet copper jacket might be seen. There are various solvents and mechanical cleaners for this purpose, and we recommend that the instructions given by their manufacturer’s are followed. Badly fouled barrels can shoot inaccurately and will corrode much easier than carefully cleaned ones.
Wipe the rifle clean from dust, dirt, etc. and lubricate all metal surfaces with a lubricated rag so that a light film of lubricant remains on the rifle.
Inspect sling mounts and ensure their secure attachment to the rifle.
Disassemble the bolt as instructed in the manual, clean the dirt with solvent-wetted brush and lightly lubricate surfaces with protective oil.
Assemble the bolt and check the function of different parts (including ejectors and extractors.)
Check the attachment of the sights and scope.
Clean muzzle brake and other accessories and lubricate them if needed.
Check tightness of all screws including stock and receiver screws.
Assemble the gun and check functionality of the components.

STORAGE

Always store your firearm in a secure, dry place, where it will not be damaged and where children and unauthorized persons cannot gain access to it. Keep cartridges separately in a secure place. Before storage, always check the condition of the rifle and ensure that is it perfectly dry. Remember to remove the suppressor from the barrel (If fitted) before storage. Moisture and water drops can damage rifle.

Always follow the federal legislation and regulations concerning the storage of the firearm. Do not store the rifle in a leather or cheap fabric case. There materials attract moisture, even though they may appear to be perfectly dry.

Warning

To reduce the risk of accidents involving children or unauthorized persons, keep your firearm locked away and store the ammunition in a separate locked location.

OPERATIONAL CHANGES OR DAMAGES

If you notice any changes in the functioning of your firearm, STOP SHOOTING IMMEDIATELY! You should take the rifle to an authorized gunship if you experience any occurrences similar to the following: The function of the trigger mechanism has changed, the rifle does not fire the cartridge, the safety does not operate, there is any cartridge malfunction or a changed sound when firing.

Warning

If the rifle doesn’t fire after pulling the trigger, engage the safety, wait at least one minute and unload the rifle with extreme care as described in the corresponding section.

If the rifle is damaged while shooting, send your rifle to the dealer/importer and include:

Explanation of what has happened.
The cartridge case (With which the damage occurred).
Preferably a sample of the cartridges.

In these circumstances do not dismantle the rifle. Never ship a loaded firearm.

WARRANY

All RDSC | Shield Rifleworks products are warrantied against all manufacture defect(s). RDSC | Shield Rifleworks products are not covered under warranty from issues or damage caused by operator error or negligence. For 3rd party products, we do not refer our customers directly to 3rd party manufacturers for warranty. We prefer to handle all claims, "in house". In extreme cases we will replace the warrantied item ourselves and then claim it back from the manufacturer at a later date. We will also cannibalize parts from new in-stock products if necessary to expedite claims. Under no circumstances attempt to return products direct to a manufacturer without first consulting with us. With all claims we need a copy of your sales receipt or the order number.